![]() ![]() With your program open in RSLogix, select “ Who Active” from the “ Communication” menu. Download your programĪt this point, your PLC is ready for operation. If you’re having issues with the BootP/DCHP tool, check out Lillian’s blog post for tips. If not, try this step again until the IP settings stick. If the PLC retains its IP address, go ahead and move on to the next step. It’s always a good idea to stop at this point and power cycle the system. Wait for the a successful confirmation message. Locate your PLC by its MAC address and choose “ Add Relation.” Next, right click on the PLC (now in the lower window pane) and choose “ Disable BootP/DHCP.” Enter the desired network settings and click OK. To disable BootP and give the PLC a static IP address, you’ll need another Rockwell tool called BootP DHCP EtherNet/IP CommissioningTool. This makes life much easier in the future, especially with integrating SCADA, remote access, and device troubleshooting. However, DMC finds that best practice is to setup static IP addresses for all devices on the control network. The factory default for Allen-Bradley PLCs and many peripherals is to ship with BootP/DHCP enabled. That means you’re ready to assign IP addresses. ![]() If you are doing this on a live system – STOP! When the firmware upgrade completes, the PLC will begin scrolling its MAC address across its display (if applicable). Accept all the warnings that tell you not to do this on a live system. Navigate to the PLC in RSLinx and click OK. With an Ethernet cable connected directly between your PC and the PLC, follow the prompts to select your model number and firmware revision. To do this, you’ll need a Rockwell tool called ControlFLASH. Believe me, it’s as exciting as the icon makes it look, just without the lightning bolts. Now what? If it’s fresh out of the box, you’ll likely have to install the firmware. Once you've accomplished this, give yourself a pat on the back and read on! Firmware SetupĬongratulations, you’ve just powered up your shiny new Allen-Bradley PLC for the first time. You'll also need a PC with all the relevant Rockwell software installed. All the information covered here is also available in Rockwell’s help documentation, but I tried to distill out the most important bits to get you off the ground as fast as possible.īefore we start, you'll need all of the components networked together and powered on. Learn more about DMC's Factorytalk expertise and contact us for your next project.In this blog, I’ll walk you through the basic commissioning steps to get a brand-new Allen-Bradley PLC and HMI up and running. The only drawback to the Command Line is that it has a limit of 5000 characters at a time, but this is pretty easily worked around by splitting up the commands you enter into groups less than that number. These could be copy-pasted by the customer into the Command Line and entered to update all the fields at once. This could be done via Rockwell's Studio 5000 Application Code Manager (ACM) or individually via the PlantPAx faceplates however, because the software was being commissioned and tested onsite by the customer, it was much easier and faster for us to use excel to create a list of commands. For instance, we recently had a system with over 100 interlock conditions that required string descriptions to be entered on a system being commissioned. I have leveraged this feature the most for managing bulk updates on a PlantPAx system. It's usually beneficial to have the Diagnostic List up as well to verify that the commands were executed successfully.Īfter hitting Enter, we can see that the write was successful. ![]() Hit Enter to execute the command, or set of commands. Clicking this opens a blank text window with an ellipsis button in the top right.Ĭlicking the ellipsis gives you access to the Command Wizard, which allows you to select and create commands similar to how you would on a button object.Īfter creating your command, it will appear in the Command Line. The Command Line can be accessed from the project tree under the System Folder. During last year's ROKLive event in Orlando, I learned about a feature in FactoryTalk View Site Edition that I have already begun leveraging in all my projects: the FactoryTalk View Studio Command Line. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |